Welcome to use the 30CH constant decoder, which take advantage of advanced microelectronic control technology. This technology changes the international fashion DMX512/1990 standard
digital control signals into analog control signals. There are 1 ~ 30 output channels; each channel can achieve 256 control levels. This constant decoder is used when DMX512 control equipment
control general LED lighting.
Products Performance:
Input Power: DC9V-DC24V
Maximum load current: 1A/CH×30
Maximum power load: 360W (12V) 720W (24V)
Output gray level: 256
Input Signal: DMX512/1990
Output signal: 30 channels Constant PWM
Output DMX : 30 channels
standard XLR-3 caron plug
Size: L225*W80*H32
Gross Weight:300g
Basic functions:
There are 30 output channels, can connect with single or RGB lamps
0-100% dimming output, each channel 256 gray levels
International standard DMX512 input protocol, address code set by DIP switches;
Wide voltage DC input DC9V ~ DC24V;
Each occupied by 30 DMX address.
The decoder comes with 16 kinds of test patterns, 16 levels for rate of change
Decoder to use:
Note: FUN = OFF (the tenth code switch up) means to accept DMX512 signal mode
The first DMX address setting:
The decoder set the address bit by coding switch, of which 1-9 is for setting the start address of the Binary numeric code switch of DMX512, the first one is the lowest position,
the ninth one is the highestBit of address code can be set to 255.
DMX512 start address code is the sum of switches 1-9, at the same time turn downside of the code switch (ON set to “1”), then the value of the bit can be gotten; coding switch
up (set to “0”), the value of the bit is 0.
Example 1:
As the following Schematic 1, DMX512 start address is set to 38, encoding the No. 6,3,2 position on switch dial to “1”, others set to “0”, then the sum of the switch 1-9 code value is
32 + 4 + 2, that is the DMX512 start address 38
Schematic 1
Example 2:
As the schematic 2, DMX512 start address is set to 388, encoding the no. 2,3,6,8 switch dial to “1”, others set to “0”,, then the sum of the switch 1-8 code value is 4 + 128 + 256 = 388,
that is the DMX512 start address 388.
Schematic 2
Operation instruction for the automat effect
Note: It will be Automatic operation mode when the No. 10 switch is turned down.
Effect choice (button switch No.1 to No.4):
1, Push No.1: Automat cycling.
2, Push No. 2: Seven-color gradual cycle changing.
3. Push No.1 &2: RGB Fade in and out
4. Push No.3: Severn color jumping
5. Push No.1 & 3: RGB jumping.
6. Push No.2 & 3: Red color.
7. Push No. 1 & 2 & 3:Green color.
8. Push No.4: Blue color.
9. Push No.1 & 4: Yellow.
10: Push No.2 & 4: Violet.
11. Push No.1 & 2 & 3: Cyan.
12. Push No.3 & 4: white.
13. Push No.1 & 3 & 4: Seven-color gradual cycle changing and jumping.
14. Push No.2 & 3 & rgb-color gradual cycle changing and jumping.
15. Push No.1 & 2 & 3 & 4: Seven-color jumping and rgb-color jumping.
Speed Choices (Button Switch No.5 to No. 8)
1. Push No.5: 0.5 second. 2. Push No.6: 1 second. 3. Push No.7: 1.5 second. 4. Push No.8: 2 second.
Schematic for System Connection:
If used tow or more power supply ,you can connect as follows
Installation Notes:
1 This kind of controller works only under DC9V-24V, which is provided by the matched controllable main power, or else the controller will be damaged.
2 The UTP wire is connected hand in hand to make the cable, when two or more controller connected.
3 The power supply should be off when connecting the electric wires, and it can be turned on till making sure the wires are connected correctly and the indicator of main power in red is lighting.
4 Controller should work under the environment of adequately ventilated, dry, not corroded, no flammable gas and rust.
5Please check the wires connection regularly so that the wires of aged, rust-eaten, and damaged insulation spacer can be replaced timely
Simple troubleshooting and maintenance:
Symptom |
Reason Analysis |
Solution |
NO lighting |
1,No power 2,Wrong connection of wire 3,Power protection setting |
1,check power supply 2,check wire connection 3,check power failure, power on again |
Red indication light is on, green indication light not flash |
Didn’t make dip switch or dip switch is not in correct |
Follow up the instruction to reset dip switch |
The Light color is not show in correctly |
1.RGB LED is not connection correctly 2.Dip switch is not in correct place |
1, Re-connect the RGB and wire 2, Reset dip switch |
Can’t be synchronization |
1,The RJ45 cable is not connected or wrong connection 2,master and slave controller setting failure,The slaver is set dip switch effects |
1,re-connect the RJ cable 2,reset master and slave controller to ensure only one master |
Led brightness is different at beginning and end |
1, Output line is too long 2, The diameter of wire is too thin 3, Overload working |
1, Use annular electric supply or shorten circuit 2, Calculate electrical current, change strong wire 3, Change power or increase controller |
0 out of 5 (0 Ratings)
Positive (0%) |
5 Stars (0)
|
4 Stars (0)
|
|
Neutral (0%) |
3 Stars (0)
|
Neutral (0%) |
2 Stars (0)
|
1 Star (0)
|
Name | Rating | Feedback |
---|
Shipping Company | Shipping Cost | Estimated Delivery Time |
---|---|---|
3 - 7 days | ||
3 - 7 days | ||
5 - 14 days | ||
Post Air Mail | Free Shipping | 15 - 45 days |
Return Policy | If the product you receive is not as described or low quality, the seller promises that you may return it before order completion (when you click "Confirm Order Received" or exceed confirmation timeframe) and receive a full refund. The return shipping fee will be paid by you. Or, you can choose to keep the product and agree the refund amount directly with the seller. N.B.: If the seller provides the "Longer Protection" service on this product, you may ask for refund up to 15 days after order completion. |
---|---|
Seller Service | On-time DeliveryIf you do not receive your purchase within 60 days, you can ask for a full refund before order completion (when you click "Confirm Order Received" or exceed confirmation timeframe). |
Most Popular from Category
Mini RGB Controller Dimmer 12V 6A 3 Keys for 5050 3528 RGB LED Strip Light 19 Dynamic Modes and 20 Static Color Free Shipping
US $1.78 / piece
2.4G touch screen DC12-24A 18A RGB led controller RF remote control for led strip/bulb/downlight
US $15.40 / piece
2014 New Cheap Mini RGB Controler Dimmer Switch For 5050 3528 SMD LED Lights Strip DC 12V
US $1.06 / piece
1pcs free shipping New 12V 6A 44Key RGB MINI IR Remote Controller for SMD 3528 5050 5730 5630 3014 RGB LED SMD Strip Lights
44 Keys LED IR RGB Controler For RGB SMD 3528 5050 LED Strip LED Lights Controller IR Remote Dimmer Input DC12V 6A Free Shipping
US $2.80 / piece
Dimming Controler LED Dimmer Direct Current 12V Single Color Adjustable For 5050 3528 LED Light Strips Dimmer Controller
US $5.96 / piece
online shopping, buying directly from manufacturers?
- Go to Alibaba.com and enter the wanted item into search field.
- Having made your choice, click "Contact supplier" button on the right
- On the next page enter your request and click "Send" button.
- Upon clicking you will be asked to get registered. Do it and wait for the reply.